Відео

That's incredible i never would have thought of that mate brilliant many thanks greatly appreciate the video ❤

Scroll saw blades use according wood thickness

Nice cuts !! The first part of the video your hands are in the way of the cut ,, Great video 👍

Thanks so much for these tutorials, they really are excellent. As an absolute beginner they've made a huge difference.

Woof!!

Woof!!

👌

Thanks for the To The Point video - with NO stupid music. I always tension my blades starting out but, never after 10 seconds and almost never after I start sawing. My bad (stupid). This made such a big difference in my cuts. Thanks again!!!

The bottom blade clamp isn’t moving, how can I fix it?

Thank you! Explains so much.

Good info, just starting to use a scroll saw, thanks!

I Whent & Bought Me Some Number 10 Blades & They'er Carbin Steel Wich I Think Is Pretty Durrable For Cutting Maple & Oak Or walnut. I Get My Wood From PaletsWich Are Free To Me

I Was Cutting Out A Heart Shaped Spoonrest From An Old Maple Cutting board. & That Maple Is Pretty Hard To Cut.

this is a old video and perhaps scroll saws have changed the way the blade is clamped. The clamps now allow the blade to pivot slightly due to the end having a movable tip.

where do u get sanding pads

In terms of blades cutting to the right, if you buy Olson Precisin ground blades, they remove the burr on the right side of the blade to keep it cutting straight.

Website doesn't work any more

ohne Absaugung Anfänger

What buffing pads and sanding pads are you using here please?

Thank you it has been very informative. I will start with a simple patern and see if I can do it .

What blade was used in this demonstration? I am looking to cut 3/4" pen blanks on a 90 degree zig zag all the way down without removing it at any point, so I need clean and perfect 90 degrees in order for this to work. I haven't the foggiest idea what blade to select for this very purpose. Cheers!

Great Thank you

Thank you. What is the best wood to use and which blades to use

Hi Bob, I am real new within this scrollsaw approach but even these video's are a few years old, it really helped me for doing it in the proper way. So thank you very much for it and no reasons to apologise. It's about the content and that's what you're doing very good! Thx

This is a great video! I always wondered how to use a scroll saw.

Thank you

❤❤❤❤❤❤

How would you fix it had multiple turns and corners? Just recut or same way? Thanks

Thanks

If you could put a musical note or sound to how much tension is optimal for most blades what sound would you say it might be? In my experience over the last 10 yrs that average tone sound is equivalent to about notes of "A," "B," or "C" depending on the thinness of the blade - thicker blades more towards the note of "A," whereas the skinnier they are, more towards the higher note of "C." Thoughts?

Hey ! thanks for sharing that tip. 👍🏻I learn something every day on the UA-cam.

Thanks! Just the video I needed! One question. Why not take a square, draw line on wood and adjust the table?

Fine

🎉

That blade didn’t stretch, stop being a goofball the scroll lever was down and when you turned on the machine it went up

We have used the ua-cam.com/users/postUgkxOTeIs0vv4_9B5hsmnLsk9r930uDQLu_Y for probably 30 hours with our camper and it’s been great! The noise level is really only noticeable when running the AC and other appliances like the microwave, hair dryer, or coffee pot. It’s not huge like other ones and it has wheels so even at 90lbs, I can move it!

Worth the money

Worth the money

Hi whatvfont did you use on this

5:05 so, technically speaking it's never going 2 b a perfectly "even" (or "flat" or whatever term is) cut surface then, right? 15:48 the distance from your finger 2 the blade kinda scares me...

good vids. 3:37 +10000B 4 using *PENCIL* 2 point @ the blade. If u added a short note 4 everybody 2 always - *ALWAYS* keep their fingers off of the blade that would b even more clear. :) also, + another 10B 4 *NOT* using any annoying bg muzak... 4:01 exactly same thing as "it's the photographer who takes a picture, not the camera". it's not the saw which's cutting your wood, it's the woodworker.

I obtained an older Dremel 57. It feels like it will jump off my workbench @ any second. Is it expected with older scrolls?

Have jet 22 inch the blades suddenly not been picked up by the clamping system. 5 inch blades seem too short. It was fine when the machine was new. Had it about a year.

Thank you so much.

A question for you, and I'll be grateful to hear from you. I use an excalibur 21. It seems that the blade tension changes with the position of upper arm. For example, when I stop cutting, loosen the blade, and put it in another hole to cut, if the upper arm is high, the tension will be less. and if the upper arm is low, the tension will be more when I turn the knob. Can you help me to make it consistent?

This was extremely helpful! Thank you! I see you have not put out any videos in a while, will you be coming back?

Very good thank you for good instructions

Oh knew a James bloodsworth, FL. Very unusual name

No hurry, no hurry..over over my teacher said. Correct is better, turn turn earlier..

Oh my, I needed to learn I could do top feed.. newbie here. I spent most of class time undoing, yrhreading blade from bottom.broke first blade today. Thank you for this great class